View ST10R172L-B0_93067.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ST10R172L-B0
16-BIT LOW VOLTAGE ROMLESS MCU
ERRATA SHEET
1 INTRODUCTION
This errata sheet describes the functional problems known in the step B0 of the ST10R172L-B0. This is the erratasheet of the ST10R172L datasheet version 1.1 of april 2000.
2 FUNCTIONAL PROBLEMS
The following malfunctions are known in this step:
2.1 ST_PWRDN.1: EXECUTION OF PWRDN INSTRUCTION WHILE NMI PIN IS HIGH
When PWRDN instruction is executed while NMI pin is at a high level, power-down mode should not be entered, and the PWRDN instruction should be ignored. However, under the conditions described below, the PWRDN instruction may not be ignored, and no further instructions are fetched from external memory, i.e. the CPU is in a quasi-idle state. This problem will only occur in the following situations:
1) the instructions following the PWRDN instruction are located in an external memory, and a multiplexed bus configuration with memory tristate waitstate (bit MTTCx= 0) is used, 2) the instruction preceding the PWRDN instruction writes to external memory or an XPeripheral (XRAM, CAN), and the instructions following the PWRDN instruction are located in external memory. In this case, the problem will occur for any bus configuration.
Note: the on-chip peripherals still work correctly: if the Watchdog Timer is not disabled, it will reset the device upon an overflow. Interrupts and PEC transfers, however, can not be processed. If NMI is asserted low while the device is in this quasi-idle state, power-down mode is entered. No problem will occur if the NMI pin is low: the chip will normally enter power-down mode. Workaround: Ensure that no instruction which writes to external memory or an XPeripheral precedes the PWRDN instruction, otherwise insert e.g. a NOP instruction in front of PWRDN. When a multiplexed bus with memory tristate waitstate is used, the PWRDN instruction should be executed from internal RAM or XRAM.
Rev. 1.0 April 2000 1/3
ST10R172L-B0 Errata Sheet
2.2 CORE.4: INCORRECT INSTRUCTION FETCH ON JUMP TO ITSELF The bug happens In the following program sequence: ... ... Label_A: JMPR cc_XX, Label_A Word Intruction 1; Word Intruction 2 Word Intruction 3 ... ... ... In the following conditions: - code is fetched from External Memory, - the loop JMPR cc_XX, Label_A is being executed,
- a PEC transfer with PSW as destination triggers a change of the condition cc_XX and so, the loop is finished, the Word Intruction1 is never executed.
Workaround: If JMPA is used instead of JMPR, the bug does not occur. 2.3 EBC.3: VISIBLE MODE When visible mode is enabled (syscon.1 = 1), data of a read access to an XBUS peripheral is not driven to the external bus (Port 0). Instead, Port 0 is tri-stated during these read accesses.
If all external devices are configured in 8-bit demultiplexed mode, an XBUS-peripheral write can cause a conflict on P0H (Port 0 [8:15]).
2.4 EBC.4: XPERS ACCESS IN XPERSHARE/EMULATION MODE In emulation mode and if the Startup Configuration 8-bit multiplexed mode is selected, P0H (Port 0 [8:15]) is always an output and write accesses to XPERs cannot be done as these would cause a conflict. Workaround: Use a Startup Configuration other than 8-bit multiplexed mode. If HOLD mode is entered (P6.5 = 0) following an 8-bit multiplexed mode access and if Xpershare is enabled, Xper accesses will cause a conflict on the internal XBUS xb_data [15:7] bus. Workaround: None.
2/3
ST10R172L-B0 Errata Sheet 3 HISTORY OF FIXED FUNCTIONAL PROBLEMS OF THE ST10R172L:
fixed in Step B0 B0 B0 B0 B0 B0 B0 B0 B0 B0
Functional Problem CPU.17 TRAP_B.1 Kfm_BR03 Kfm_BR04 Kfm_BR05 CORE.3 CORE.4 CLK.1 DAD.6 DAD.7
Short Description
Arithmetic Overflow by DIVLU instruction ATOMIC / EXTended sequences in Class B Hardware Trap Pipeline conflict after CoStore operation Wrong PSW value after byte instruction Wrong result for BFLDL/BFLDH instructions Incorrect instruction fetch on Cache Jump Incorrect instruction fetch on Jump to itself ADAPT mode entered during power-up synchronous reset Incorrect PEC source fetch after JMPS instruction Incorrect pipeline dependency detection between DPRAM and (E)SFR address space
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (c)2000 STMicroelectronics - All Rights Reserved. Purchase of I2C Components by STMicroelectronics conveys a license under the Philips I2C Patent. Rights to use these components in an I2C system is granted provided that the system conforms to the I 2C Standard Specification as defined by Philips. STMicroelectronics Group of Companies Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com
3/3

▲Up To Search▲

Price & Availability of ST10R172L-B0

	To Download ST10R172L-B0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .